GODIAG Full Protocol OBD2 Jumper Functions:
 
1. Supports DC power supply
2. Support safety protection banana head super programming dedicated connection port power supply.
3. Independent GND4, GND5 [meet the needs of special ECU programming].
4. With boot GND4 clip, compatible with programming equipment such as MPPS, FGTECH, KESSV2.
5. With GND4 GND5 short-circuit switch [some ECUs need to be switched to short-circuit mode when programming].
 
Note: The switch of GND4-5 is normally pressed to make it light. When some ECUs need to be independently connected to GND4 and GND5, release the switch.
 
6. With ignition analog switch [equipped with 1 large and 2 small dedicated ignition cables].
7. Support standard obd2 full protocol connection [double K line, double CAN line], 3 large and 2 small power plugs, 4 large GND, 4 small GND.
8. Equipped with CAN protocol communication resistance.

What is the analog ignition switch?
 
After the ING ignition switch is pressed, the line marked with ING12V will have 12v, which is the analog ignition switch. Because when some devices read some ECUs, the device will prompt to turn on or off the ignition switch.

Workable Models and the Data Acquisition Time:

Mercedes Benz S series
Chassis W221 EIS model 216 free of disassembly,free of plugging in and out,acquisition time of 12 minutes

Mercedes Benz E series
Chassis W221 EIS model 211 free of disassembly,free of plugging in and out,acquisition time of 9 minutes

Mercedes Benz C series
Chassis W209 EIS model 209 free of disassembly,free of plugging in and out,acquisition time of 9 minutes

Mercedes Benz B series
Chassis W246 EIS model 169 free of disassembly,free of plugging in and out,acquisition time of 35 minutes

Mercedes Benz A series
Chassis W246 EIS model 169 free of disassembly,free of plugging in and out,acquisition time of 35 minutes

Mercedes Benz R series
Chassis W251 EIS model 164905 free of disassembly,free of plugging in and out,acquisition time of 12 minutes

Mercedes Benz ML series
Chassis W164 EIS model 164905 free of disassembly,free of plugging in and out,acquisition time of 12 minutes

Mercedes Benz GL series
Chassis W166 EIS model 164905 free of disassembly,free of plugging in and out,acquisition time of 12 minutes

 GODIAG Full Protocol OBD2 Jumper Cable is used to connect ECU, Immobilizer, ABS, Airbag, Instrument cluster via OBD or bench easily
The jumper is compatible with lots of OBD2 devices, ECU programmers, key programmers, airbag reset tools and mileage programmers.
can work with Key Tool Plus, Autel IM608 II, Launch Tablet Diagnostic,CGDI, OBDSTAR, KESS V2. 

The CAN FD Adapter from Autel is designed to connect to compatible vehicle communication interfaces (VCIs) to enable its tablets to communicate via the CAN FD (flexible data-rate) communications protocol and diagnose the vehicle. Vehicles currently using the CAN FD  protocol include many General Motors and Ford 2019 and 2020 vehicles. Autel's MX808, MS905, MS906, MS906BT, MS906TS, MS908, MS908S, MS908P, MS908SP, MSELITE, IM508, and IM608 tablets will be able to diagnose CAN-FD equipped vehicles when the adapter is plugged into the VCI directly as in the case of the smaller VCI units or into the OBD-II cable that is connected to the larger VCIs and into the vehicle's OBD-II port.

• Autel APB112 Smart Key Emulator
• Supports 46, 4D Data Collection
• Supports 46 Smart Key Password Calculation
• Supports 46 Chip Emulation
• Supports Toyota4D (94/D4, 98) Smart Key Emulation
• Supports Toyota H (88/A8, A9, 30) Smart Key Emulation