CG FC200-MPC5XX Adapter for BOSCH MPC5xx Read/Write Data on Bench

PN: FC200-MPC5XX-P02-M230102

FC200 Software V1.1.3.0 adds BOSCH MPC5xx platform mode ECU:

(A) BOSCH ECU (Add BOSCH MPC5xx platform mode ECU)

ME9.0

MED9.1

MED9.5

MED9.5.10

EDC16C2

EDC16C8

EDC16CP31

EDC16CP35

(C) KEFICO ECU

CPEGD2.20.x

(D) DELPHI ECU (Add Mercedes Benz CRD2. x MPC556x engine platform mode)

Differences Among OBDSTAR Key Master DP Plus C Package (Full Version), A Package:

Key Master DP Plus C Full Configuration Diagnostic Function:

• Diagnose the electronic control system of prevailing vehicle models covering Asian, European, American and Chinese. Diagnosis functions include: Read DTCS, Clear DTCS, Read data stream, Special functions etc.
• Classify special function: ABS, EEPROM Adapter, Battery match, CVT learning, EPB, Gear learning, Immobilizer, TPMS (low tire) reset, Cluster calibrate, ECU programming, steering angle reset.
• Specially designed for Android platform with clear and user-friendly interface.

Key Master DP Plus C Full Configuration Software Advantages:

1 ECU Clone

ECU Clone, means ECU duplication.

The device copies all the data from the original vehicle ECU, and then writes all data copied into ECU with the same hardware to realize the same ECU function with the original vehicle.

2 Clone directly when replacing a new or a used ECU

Without online matching in the 4S store or removal of ECU bonding wire for reading and writing! Directly write without dismantling OBD!

3 Three features for ECU Clone:

1. Free of 4S online: break monopoly from 4S, benefiting automobile maintenance industry
2. Simplified operation procedures: realize foolproof operation
3. Non-dismantling with zero risks: read and write data without dismantling ECU

Switch activation function:

(Today many instruments or audio of vehicles activate secondary power supply to go into power-on status by relevant module CAN communication on the vehicle, but sometimes an instrument or an audio is separated from vehicle CAN BUS network, causing startup failure when it needs to be repaired by an auto technician. This function can simulate CAN communication to activate secondary power supply, so the instrument or the audio enters into power-on status. In this way, it not only can test and verify the instrument or the audio, but also save an enormous cost for an auto technician to purchase a large number of startup platforms of various vehicles and wiring harnesses!)

Add “Help “functions:

• Contain built-in testable vehicle models, upgrade announcement, features, help notes and wiring diagrams, etc.
• Car list: directly get it on the device
• Upgrade Announcement: all details are available on the device
• Customers can look up the features or uniquely support functions on the device
• Help notes: built-in help notes for each model or function
• Wiring diagrams: built-in ECU wiring diagrams, more intuitionistic and convenient

OBDSTAR Key Master DP Plus C Full Configuration Hardware Advantages:

• Built-in VCI box, communication more stable
• 8-inch touchscreen, more intuitionistic
• Can be charged directly via OBD interface
• Practical and high-end gift box
• Industrial design with silicone case
• Back bracket design: Can propone the steering wheel or stand on the table, easier to operate
• With simulated key 1 applies to the vehicle with 94/D4 type of smart key.
• 3 in 1 P001 programmer: combined with EEPROM adapter + RFID adapter+ Key Renew adapter
• Add the clip of reading SOP 8PIN EEPROM
• Add wiring harness of ECU reading by OBD (for ECU cloning and switch activation)
• Maintenance Database
• Remote Assistant
• One Key Upgrade

Features

• Samsung Exynos 5260(2GB ROM)
• 10.1”1024x768 LCD capacitive touchscreen
• Internal reliable 64GB Memory
• Android Operating System for fast boot-up and multitasking
• Powerful combination of key programming/all system diagnostics/advanced maintenance services
• Smart Mode for guided and automated key learning
• Expert Mode for advanced key learning
• Read PIN/CS (all key lost) , key generation, key learning, remote learning
• IMMO ECU reset/adaptation, refresh/coding
• Transpronder read/write, EEPROM/MCU read/write
• Powerful OE level diagnostics for more than 80 US, Asian and European makes and models 
• Advanced maintenance services including EPB, DPF, SAS, Oil reset, and BMS

Autel MaxiIM IM608 IMMO Vehicle List:

Audi: A1, A3, A4, A5, A6, RS4, B6, B7, RS5, RS6, A4 Allroad, A8, S8, Q3, RSQ3, Q5, Q7, R8, TT
Seat: Alhambra, Altea, Cordoba, CupraLeon, Exeo, Ibiza, Leon, Mii, Toledo
Skoda: Citigo, Fabia India, Fabia, Kamiq, Karoq, Octavia, Rapid India, Rapid, Roomster, Superb, Yeti
VW: Amarok, Arteon, Atlas, Beetle, Bora, BoraGli, Caddy, Crafter, EOS, Fox Africa, Fox EU, Fox, GTI, Gol County, Gol(5U), Gol(5W), Golf PLUS, Golf/Rabbit(1K), Golf6 ESTATE, Jetta, Parati, Passat, Phaeton, Polo, Scirocco, Sharan, Suran, T-Roc, Tiguan, Touareg, Touran, Transporter5/Multivan, up, UP!/cross UP!
Fiat: 500, 500L, 500X prox, Albea, Boxer, Daily, Doblo, Doblo New, Ducato, Egea, Fiorino, Freemont, Idea, Grande punto, Jumper, Linea, Marea, Nemo, Ottimo, Palio, Palio RST, Panda, Perla, Promaster, Punto, Sinea, Stilo, Viaggio

OE- Level Diagnostic For 80+ Vehicle Makes

Compatible with over 80 US, Asian, and European vehicles, the Autel IM608 goes far beyond communicating with all systems to access all available modules:

• Exceptional OE-Level system coverage for all electronic systems;
  
• Active Test for getting access to specific subsystems and performing component tests to drive the actuator so as to determine the integrity of the system or parts;
  
• Complete capabilities for codes, live data, active test, ECU information, adaptation, matching, etc.;
  
• Smart AutoVIN technology for identifying vehicles easily;
  
• Automatic system and software updates with real-time push message notifications via Wi-Fi;
  
• Cloud-based Data Manager saves customer and vehicle records, scanner data and technician notes;
  
• Instant remote control tech support anytime, anywhere.

Functions:

ADVANCED IMMO & KEY PROGRAMMING

Connect the IM608 tablet to the vehicle (via the Bluetooth VCI or Main Cable) and to the XP400 (via USB cable) to access IMMO related functions, including Key Learning, Remote Control Learning, Remote Control Add, etc. The software provides two methods to access IMMO functions.

• Smart Mode – for Guided and Automated Key Learning - automatically identify the type of anti-theft system, intelligently combining the matching process. Easy to use. You only need to operate according to the device prompts to perform relevant operations. A novice user can also perform Key Learning.
• Expert Mode – for Advanced Key Learning - meet the needs of professional technicians. It is more powerful for its advanced key learning functions

1. PIN / CS Reading (Full Lost)
   
2. Key Generation
   
3. Key Programming
   
4. Command Introduction
   
5. Backup / Repair IMMO Data
   
6. IMMO ECU Brain Reset / Adaptation
   
7. IMMO ECU Brain Reset / Coding
   
8. BENZ 3rd Generation IMMO Key Splicing, Full Lost, Key Programming
   
9. BMW FEM / BDC Key Programming and ECU Adaptation
   
10. BMW CAS4 / 3/2 Key Programming
    
11. VW / AUDI MQB Key Programming, 48 Transponder (96-bit) Key Splicing, Full Lost, A6 Full Lost and More ...

Professional Vehicle Locksmith

The Key Programmer XP400 is specially designed to read transponder data (including Mercedes Benz infrared smart key), clone and generate exclusive keys, read/write on-board EEPROM data, and read/write Freescale 9S12 MCUs. By working with diagnostic tool or PC those are both loaded with programmer software, the XP400 can read/write transponder data quickly and accurately. The XP400 include 9 parts:

• Transponder Induction Area – Remote control
  
• Transponder Slot – Hold the transponder
  
• Mercedes Infrared Key Slot – Hold the Mercedes infrared key
  
• Vehicle Key Slot – Hold the vehicle key
  
• IC Card Induction Area – Read/write IC card information
  
• Status LED – Indicate current operating status
  
• Cross Signal Pins – Hold the MCU board, MCU spare cable or DIY signal interface
  
• EEPROM Component Transponder Slot – Hold the EEPROM plug-in transponder or EEPROM socket
  
• Locker – Lock the EEPROM component transponder slot to ensure proper function

Note: You can connect it to the XP400 (no vehicle connection required) to access the key chip, read, retrieve and write key information, as well as other key related functions.

All-in-One Key & Chip Programmer XP400 Pro

Connect the IM608 Pro tablet to the XP400 Key Programmer (no vehicle connection required) to access the key chip, read, retrieve and write key information, as well as other key related functions. The XP400 includes 12 ports:

1. DC Port – provides 12V DC power supply.
   
2. USB Port – provides data communication and 5V DC power supply.
   
3. DB 26-Pin Port – connects with the Mercedes Benz infrared cable, vehicle key cable, ECU cable, MCU cable, MC9S12 cable.
   
4. Cross Signal Pins – holds the MCU board, MCU spare cable or DIY signal interface.
   
5. IC Card Induction Area.
   
6. Vehicle Key Slot – holds the vehicle key.
   
7. Transponder Slot – holds the transponder.
   
8. Remote Control Transponder Induction Area Figure 2-5 XP400 Views 11
   
9. Mercedes Infrared Key Slot – holds the Mercedes infrared key.
   
10. Status LED – indicates the current operating status.
    
11. Locker – locks the EEPROM component transponder slot to ensure proper functioning.
12. EEPROM Component Transponder Slot – holds the EEPROM plug-in transponder or EEPROM socket.

XP400 Key SWITCH & CHIP PROGRAMMER

1. PC Supported
   
2. MCU / EEPROM Chip Read / Write
   
3. ECU Read / Write
   
4. MC9S12 Encrypted Chip Read / Write
   
5. Key Reading / Writing
   
6. Mercedes Infrared Key Reading / Writing
   
7. Finding the Control Frequency
   
8. IC Card Reading / Writing

All System Diagnostics - Access to OE-Level Diagnostics

This OE-Level diagnostic tool allows you to perform the same level of analysis, diagnosis and repair as the OEM dealer’s tool does, which means, as a professional mechanic, you now have full access to all of the diagnostic information as the same exact tool that of the OEM dealer offers, and the ability to complete reflashing or reprogramming without outsourcing or turning a client away. Also, this access to information will be a substantial improvement for independent repair shops

1. All System Diagnostics
   
2. Auto Search / VIN Finding
   
3. Reading / Deleting Error Code
   
4. Viewing the Live Data Stream
   
5. View Records of Failure History
   
6. Store and Data Management Applications
   
7. MaxiFlash JVCI ECU Programmer (Bluetooth / USB Cable)

Auto Scan & Auto VIN for Added Convenience

Adopting the latest VIN-based technology, Autel IM608 comes with Auto VIN feature to acquire the vehicle VIN number automatically and Auto Scan feature can quickly scan all modules present to quickly locate the fault cause at one touch.
The AutoVIN Scan technology of the IM608 enables you to identify CAN vehicles fast and precisely in one touch. With this advanced function, you can easily and quickly retrieve car's information, including the vehicle type, country of origin, engine size, etc. and run diagnostics on selected system.

ECU Coding

The Coding function is used to re-flash the vehicle control modules, it allows you to update the computer software on the
vehicle to the latest version, as well as to reprogram adaptive data for certain components after making repairs or
replacements, providing ways for the issues of Drivability, Fuel Efficiency, Power Loss, Fault Codes, Durability of Mechanical Parts.

Active Test

The process of sending and retrieving information from a vehicle control module with a device is known as Actuation test or bi-directional control. The main aim of the actuation test function is to request the control module to perform a specific function including system tests, actuator tests, functional tests, inspection tests, reprogramming or reinitialization, thus saving diagnostic time. 

Eg: You connect a fuel pressure gauge, cycled the key and cranked the engine but you couldn’t figure out anything regarding the fuel pressure. With the actuation test function of this diagnostic tool, you can send a fuel pump command on instruction and see the proper fuel pressure, figuring out if there is a problem with the fuel pump circuit or pump.

• Autel G-BOX3 Key Programming Adapter
• MaxiIM Key Programming Tablet Accessory used with the XP400
• Mercedes-Benz All Keys Lost, Faster Password Calculation
• Mercedes-Benz All Keys Lost, No More Repeated Insertions and Removals of IR Simulator
• Mercedes-Benz All Keys Lost, Can Be Programmed on the Vehicle Without Removing the EIS
• BMW DME/DDE ISN Reading and Writing in Boot Mode or Bench Method
• Contains All Connections Including Cables, Fuse Connector, and CAN Line Connectors

GODIAG Gearbox Cable 9-in-1 Set for V-A-G V30/ DQ200/ DL501/ VL300/ VL381/ DQ500/ DQ250/ DQ380/ DQ381/ DQ400E/ DL382 

Highlights:

1. Supports connections to the AUTEL G-BOX, XHORSE MULTI-PROG, and all other OBD2-connectable devices, including the OBD2 BENCH PCMflash FC200, KESSV2, for diagnostics, data read/write, and cloning.
2. Supports V-A-G Gearbox V30/DQ200/DL501/VL300/VL381/DQ500/DQ250/DQ380/DQ381/DQ400E/DL382 for direct connection to the AUTEL G-BOX and XHORSE XDMPG0GL MULTI-PROG.
3. Equipped with an OBD2 BENCH adapter, it allows for connection to a wide range of devices.
4. Can also connect to our GODIAG GT107+ DSG Plus Gearbox Data Adapter  for automatic and manual PCMflash reading/writing.

Compared with GODIAG Gearbox Cable 7-in-1 Set  GODIAG Gearbox Cable 9-in-1 Set has the following new features

1. Adds DQ400E/DL382
2. Equipped with an OBD2 Bench connection adapter, allowing for connection to a wide range of devices.
3. Can connect to a GODIAG GT107+ DSG Plus Gearbox Data Adapter for automatic and manual PCMFlash reading and writing.
4. The adapter can directly connect to the AUTEL G-BOX, XHORSE XDMPG0GL MULTI-PROG.
5. The adapter includes a DIY OBD2 CANBUS K-Line connection. It also supports DIY OBD2 Bench setups.

GODIAG GD101 J2534 Highlights:

1. Support J2534 and ELM327 mode in one device. Switch mode automatically.

2. Compatible with Honda HDS 3.104.024, Toyota Techstream V17.30.011, JLR SDD V163, Forscan 2.3.48, scanmaster v2.1, pcm-flash 1.2.0, VAG ODIS 9.1.0 and Renault Clip V227.

3. GODIAG GD101 J2534 has the similar functionality as Tactrix Openport 2.0.

4. More speedup. Faster communication and reprogramming.

5. More stability. Never let you down while reprogramming.

6. Portable and convenient. Small package and easy to carry.

7. Wok on Windows 8/10/11, 32/64bit

8. Multi-Languages Available:

ODIS: English, Japanese, Portuguese, Romanian, Korean, Dutch, Polish, Turkish, Spanish, French, Italian, Croatian, Danish, German, Swedish, Finnish, Slovenian, Czech ,
Russia, Greece, Chinese

Toyota: English, French, Spanish, Japanese, German, Italian, Russian, Turkish, Chinese

Honda: English, German, Czech, Dutch, Finnish, French, Greek, Hungarian, Italian, Norwegian, Polish, Portuguese, Russian, Slovenian, Spanish, Swedish, Turkish, Japanese ,Chinese

JLR SDD: German, English, Spanish, French, Italian, Dutch, Portuguese, Russian, Japanese, Chinese, Korean

Forscan: English, Russian, Polish, Italian, German, Hungarian, Turkish, French, Latvian, Bosnian, Finnish, Romanian, Portuguese, Traditional Chinese, Simplified Chinese, Czech, Lithuanian, Slovak , Ukrainian

Scanmaster elm 327: English, Czech, German, Spanish, French, Hungarian, Italian, Polish, Serbian, Turkish, Danish, Croatian

Pcmflash: English, Russian

Can Clip Renault: English, German, Danish, Spanish, Finnish, French, Italian, Norwegian, Dutch, Portuguese, Romania, Swedish

GODIAG GD101 J2534 OBD2 Openport 2.0 Features:

1. Support most all of J2534 compatible software (HDS, TIS, ODIS, JLR SDD, PCMFLash...). 

2. Support most all of ELM327 software (ELMConfig, Forscan, ScanMaster...).

3. Support ECU reprogramming in J2534 mode with programming voltage.

4. Supply free software for diagnosing J1979 compatible vehicles.

Notice:

1. Software Free Download:
Free Download Godiag J2534 Driver V2.3
Free Download ODIS V10.0 (Password: 6vi5ku)
Free Download JLR SDD V164
Free Download Can Clip Renault V227

For Honda HDS 3.104.024, Techsteam V17.30.011, JLR SDD V163, Forscan 2.3.48, Scanmaster v2.1, PCM-flash 1.2.0 and VAG ODIS 9.1.0, please contact online customer service on Whatsapp: +86 15827245313.

2. For PCMFlash 1.20, will need to buy a PCMtuner Dongle. And only supports the OBD part. It does not support bench, boot, vag, dsg and gearboxes.

3. Not Support Win7 System

GODIAG GD101 J2534 Supported Car Models:

1.JLR SDD Software for Land Rover/Jaguar
Support for L316, L319, L320, L322, L359, L538 Land Rover vehicle lines.
Support for X100, X150, X202, X250, X350, X351, X400 Jaguar vehicle lines.

2. HDS Software for Honda
Support for Accord, Civic, Crv, City, et al.

3. Toyota
Support for Camry, Rav4, Carolina, Prius, Lexus

4. ODIS VAG
Support for Vw, Audi, Seat, Skoda

5. GM GDS2 Software
Support for Buick, Chevrolet, Cadillac, etc.

GODIAG GD101 J2534 Function List:

• Read/Clear Codes
• Perform Active Tests
• View Generic & Manufacturer Live Data
• Perform TPMS OBDII RelearnAdvanced Diagnostics
• Coding and Adaptations with MaxiSYS Tablet Tools MS906BT+
• ADAS Calibrations (requires MaxiSYS ADAS software)

Autel MaxiIM IM608 II is the newest all-in-one OBD diagnostic tool this year, combining full IMMO and programming function coverage, all system diagnostics, 36+ maintenance functions, ECU coding and ECU online programming (J2534 JVCI compatible) and more. It functions exactly the same as Autel MK908P II or MaxiSYS MS908S Pro II. 

Main Configuration Updates Based on Autel IM608 Pro:

• Operating system move on to Android 10 from Android 4.4.
• Upgraded 8-core Qualcomm SDM660 8-Core Processor replacing old Exynos T5260 6-Core Processor.
• Doubled RAM & ROM: 4GB/128GB; SD card support up to 64GB (IM608 Pro support max 32GB)
• 16MP Rear camera replacing the previous 8MP one.
• Optimazed newest Software version & More Intuitive Interface.

Autel MaxiIM IM608 II Features

• No IP Limitation: You Can Use it All Around the World without Limitation
• One Year Free Update Online (After One Year, IM608 II Software Subscription Cost $850/Year)
• Upgraded Version of Autel IM608 and IM608 PRO, with the latest powerful hardware configuration
• Smart Mode and Expert Mode Solution In One Tool to Easy Operation with Ambient Light Sensor – detects ambient brightness.
• Support Multi-Language: Both Diagnose Software and IMMO Software Support Multi-Language. (Default Language is English, Can Be Changed Language to German, Swidish, Italian, Portuguese, French, etc.)
• Works for 85% Cars In The Wordwide, Include BMW, BENZ, VW, AUDI etc. make your work simple and easier, Best Choice for Locksmith and Workshop
• Extended to Work with Autel MV108/ MV105 allowing you to examine difficult-to-reach areas normally hidden from sight. It is capable of recording digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure safely and quickly.

Autel MaxiIM IM608 II Top Highlights

Upgraded from IM608/IM608PRO, the IMMO & key fob programming tool IM608 II can also read the immobilizer pin codes and password directly from the vehicle and store the information to do key learning for the newly programmed keys. The professional key fob programming tool Autel IM608 II has covered almost all the key programming functions:

• Auto Detect Make/Model/Year/System
• Read PIN (All Key Lost), Key Learning
• IMMO ECU Reset/Adaption, IMMO ECU Refresh/Coding
• VW MQB Key Learning, Mercedes Key Learning
• B~MW FEM/BDC Key Learning and Adaption, Programming and Coding functions for lMMO related systems: DME,JBE,FRM,CAS, KOMBI,EGS, GwS,ZGW, ELV and FZD
• B~MW CAS4 Key Learning and Adaption
• Mercedes-Benz: Coding SCN for lMMO related systems;DAS, ECU, TCU, ISM and ESL
• 2015-2018 Land Rover & Jaguar write key via dump
• Volvo Smart Key Learning/knob-style smart key

Expanded adapter set for the IM608 II with the XP400PRO:

• Supports over 10 key unlock types
• BMW EWS3 key learning
• Benz NEC key learning
• Benz ESL_W209 read/write/erase

• Powerful Cortex-A9 processor
• 7”1024x600 LCD capacitive touchscreen
• Internal reliable 32GB Memory
• Android Operating System for fast boot-up and multitasking
• Powerful combination of key programming/all system diagnostics/advanced maintenance services
• Smart Mode for guided and automated key learning
• Expert Mode for advanced key learning
• Read PIN/CS (all key lost) , key generation, key learning, remote learning
• IMMO ECU reset/adaptation, refresh/coding
• Transpronder read/write, EEPROM/MCU read/write
• Powerful OE level diagnostics for more than 80 US, Asian and European makes and models
• Advanced maintenance services including EPB, DPF, SAS, Oil reset, BMS and TPMS sensor ID relearn

FEM BDC Module Testing Platform is a powerful tool for key programming. ecu coding

When making keys, for BMW F series FEM & BDC all need to preprocess the IMMO box. If there is no test platform, it needs to disassemble and install the control unit in the car back and forth. Using our test platform can be completed on the bench, It's both economical and convenient.

With your FEM/BDC keys, FEM BDC Module Testing Platform is easy to detect FEM BDC Control Module in good condition. 

CGDI A2 Key Programmer with Premium Edition IMMO Matching 

Ultimate Coverage- One Device, Multiple Functions, No Annual Fee, IMMO Matching, Frequency Detection, WiFi Connectivity.

Notice: Mercedes-Benz License Needs to Pay Separately.

Features:

• Support password-free and disassembly-free matching for most vehicle models.
• Support automatic identification of Mercedes-Benz chassis numbers with rapid data collection.
• Support password-free CANFD system matching for General Motors vehicles.
• Support Volkswagen MQB.
• Support Mazda CX-30.
• Support full smart card replacement (no physical card required) for Toyota 8A/4A systems.
• Support Honda smart key systems for models after 2021.
• Support 28-digit password-free matching for Nissan vehicles.
• Free update for BMW BDC2 systems (applicable to models from 2016 onwards).

Packing List:

• 1pc x CGDI A2 host
• 1pc x BBA Adapter
• 1pc x TY8A Adapter
• 1pc x EE Adapter
• 1pc x AC High-speed Data collector
• 1pc x Hyundai/Kia 10-pin OBD port
• 1pc x Hyundai/Kia 3-pin OBD port
• 1pc x KY01 Cloned Key
• 1pc x USB data cable
• 1pc x Nissan all key lost dedicated 16-pin & 32-pin wire harness
• 1pc x All key lost wire harness for Toyota/Ford
• 1pc x OBD wiring harness
• 1pc x DB15 wiring harness
• 1pc x Mercedes-Benz key emulation module
• 1pc x Nissan All Key Lost dedicated 40-pin wire harness